Juniper Networks 10GE-ER/OC192-IR2

0.00 ₫

Mô tả

Mô tả

10-Gigabit Ethernet 10GBASE Optical Interface Specifications

The 10-Gigabit Ethernet optical interface standards are supported on M120 routers, M320 routers, MX Series routers, T Series routers, and PTX Series routers.

To determine which transceivers support each 10GBASE standard, see Supported Network Interface Standards by Transceiver for ACX, M, MX, and T Series Routers and Supported Network Interface Standards by Transceiver for PTX Series Routers. The “Cables and Connectors” section in the description for each MIC or PIC lists which standards and transceivers are supported for that device.

Note: Some XFP transceivers can support either the 10-Gigabit Ethernet or SONET/SDH OC192/STM64 specifications. Check the standard supported for the device in which the transceiver is installed. For example, the XFP-10G-E-OC192-IR2 transceiver installed in a 10-Gigabit Ethernet PIC supports the 10GBASE-E standard. However, the XFP-10G-E-OC192-IR2 transceiver installed in a SONET/SDH OC192/STM64 PIC supports the SONET/SDH OC192/STM64 IR2 standard.

The specifications are organized by distance supported.

10GBASE-LRM Specifications

Table 1 shows the optical interface specifications for the 10GBASE-LRM standard.

Table 1: 10GBASE-LRM Optical Interface Specifications

Parameter	10GBASE-LRM
Optical interface	Multimode
Standard	IEEE 802.3aq—2006
Maximum distance	62.5/125 MMF cable, 500 MHz-km: 722 ft (220 m) 50/125 MMF cable, 500 MHz-km: 722 ft (220 m)
Transmitter wavelength	1260 through 1355 nm
Average launch power	–6.5 through +0.5 dBm
Average receive power	–6.5 through +1.5 dBm
Receiver saturation	+1.5 dBm
Receiver sensitivity	–6.5 dBm

10GBASE-S Specifications

Table 2 shows the optical interface specifications for the 10GBASE-SR and 10GBASE-SW standards.

Note: The XFP-10G-L-OC192-SR1 transceiver supports single-mode fiber and the 10GBASE-L optical interface specifications.

Table 2: 10GBASE-S (10GBASE-SR and 10GBASE-SW) Optical Interface Specifications

Parameter	10GBASE-S
Optical interface	Multimode
Standard	IEEE 802.3ae—2002
Maximum distance	50/125 MMF cable, 2000 MHz-km: 948 ft (300 m) 50/125 MMF cable. 500 MHz-km: 269 ft (82 m) 50/125 MMF cable, 400 MHz-km: 217 ft (66 m) 62.5/125 MMF cable, 200 MHz-km: 108 ft (33 m) 62.5/125 MMF cable, 160 MHz-km: 85 ft (26 m)
Transmitter wavelength	840 through 860 nm
Average launch power	–4.5 through –1.0 dBm
Average receive power	–9.9 through –1.0 dBm
Receiver saturation	–1.0 dBm
Receiver sensitivity	–9.9 dBm

10GBASE-L Specifications

Table 3 shows the optical interface specifications for the 10GBASE-LR and 10GBASE-LW standards.

Table 3: 10GBASE-L (10GBASE-LR and 10GBASE-LW) Optical Interface Specifications

Parameter	10GBASE-L
Optical interface	Single-mode
Standard	IEEE 802.3ae—2002
Maximum distance	9/125 SMF cable: 6.2 miles (10 km)
Transmitter wavelength	1260 through 1355 nm
Average launch power	–8.2 through 0.5 dBm
Average receive power	–14.4 through 0.5 dBm
Receiver saturation	0.5 dBm
Receiver sensitivity	–14.4 dBm

10GBASE-E Specifications

Table 4 shows the optical interface specifications for the 10GBASE-ER and 10GBASE-EW standards.

Table 4: 10GBASE-E (10GBASE-ER and 10GBASE-EW) Optical Interface Specifications

Parameter	10GBASE-E
Optical interface	Single-mode
Standard	IEEE 802.3ae—2002
Maximum distance	9/125 SMF cable: 24.8 miles (40 km); distances greater than 18.6 miles (30 km) are considered to be engineered links. Note: Any distance greater than 30 km requires engineered links that must be field-tested to verify the conformance of the 11 dB channel insertion loss specification. EANSI/TIA/EIA-526-7/Method A1 describes the insertion loss measurement of installed fiber-optic cables.
Transmitter wavelength	1530 through 1565 nm
Average launch power	–4.7 through 4.0 dBm
Average receive power	–15.8 through –1.0 dBm
Receiver saturation	–1.0 dBm
Receiver sensitivity	–15.8 dBm

10GBASE-Z Specifications

Table 5 shows the optical interface specifications for the 10GBASE-ZR and 10GBASE-ZW transceiver.

Table 5: 10GBASE-Z (10GBASE-ZR and 10GBASE-ZW) Optical Interface Specifications

Parameter	10GBASE-Z
Optical interface	Single-mode
Standard	Multivendor
Maximum distance	9/125 SMF cable: 49.6 miles (80 km)
Transmitter wavelength	1530 through 1565 nm 1528.38 through 1568.77 nm (tunable) for XFP-10G-CBAND-T50-ZR 1528.38 through 1568.77 nm (tunable) for SFPP-10G-CT50-ZR 1528.38 through 1568.77 nm (tunable) for SFPP-10G-DT-ZRC2
Average launch power	0 through 4.0 dBm for XENPAK-1XGE-ZR 0 through 4.0 dBm for XFP-10G-CBAND-T50-ZR 0 through 4.0 dBm for XFP-10G-Z-OC192-LR2 0 through 5.0 dBm for SFPP-10GE-ZR –1.0 through +3.0 dBm for SFPP-10G-CT50-ZR –1.0 through +3.0 dBm for SFPP-10G-DT-ZRC2 0 through 4 dBM for SFPP-10G-ZR-OTN-XT
Average receive power	–25.0 through –7.0 dBm for XENPAK-1XGE-ZR –23.0 through –7.0 dBm for XFP-10G-CBAND-T50-ZR –24.0 through –7.0 dBm for XFP-10G-Z-OC192-LR2 –23.0 through –8.0 dBm for SFPP-10GE-ZR –24.0 through –8.0 dBm for SFPP-10G-CT50-ZR –24.0 through –7.0 dBm (9.95, 10.312, and 10.709 Gbps) for SFPP-10G-DT-ZRC2 –24.0 through –8.0 dBm for SFPP-10G-ZR-OTN-XT
Receiver saturation	–7.0 dBm for XENPAK-1XGE-ZR –7.0 dBm for XFP-10G-CBAND-T50-ZR –7.0 dBm for XFP-10G-Z-OC192-LR2 –8.0 dBm for SFPP-10GE-ZR –7.0 dBm for SFPP-10G-CT50-ZR –7.0 dBm for SFPP-10G-DT-ZRC2 –7.0 dBm for SFPP-10G-ZR-OTN-XT
Receiver sensitivity	–25.0 dBm for XENPAK-1XGE-ZR –23.0 dBM for XFP-10G-CBAND-T50-ZR –24.0 dBm for XFP-10G-Z-OC192-LR2 –23.0 dBM for SFPP-10GE-ZR –23.0 dBm for SFPP-10G-CT50-ZR For SFPP-10G-DT-ZRC2: –24.0 dBm (9.95, 10.312, and 10.709 Gbps, BER <1X10^-12, no FEC) –25.0 dBm (11.049 and 11.095 Gbps, BER <1X10^-6, pre-FEC) Note: When you use SFPP-10G-DT-ZRC2 in OTU1e (11.049 Gbps) or OTU2e (11.095 Gpbs) applications, you must enable forward error correction (FEC) to achieve target receiver sensitivity. To enable FEC mode, use the fec command at the [edit interfaces interface-name otn-options] hierarchy level (see fec). –23.0 dBm for SFPP-10G-ZR-OTN-XT